SRP pistons, RC injectors, Ferrea valves

We may earn a small commission from affiliate links and paid advertisements. Terms

boostin4fun

Boosted ls/vtec ohh yeah!
First thing up for sale is a set of SRP forged pistons pn#149236. These pistons have 3600 miles on them due to a sleeve cracking on my block. The set comes with three used pistons and one new one. I bought a new one because I didnt want to reuse the piston on the cracked sleeve. The used pistons appear to be in pretty good condition; there is little to no scuffing on the skirts. There is a few white spots on the sides above the first ring land on several of the pistons. I believe this is from getting hot a couple of times during the tuning process. The pistons gave me no problems whatsoever. The cylinder walls looked great when I pulled them and I had no smoking or oil consumption issues at all. These pistons yield 8.8:1 in a ls/vtec with b16 head. These are a great pistons for a factory sleeve build because they are .25mm oversized allowing you to clean the cylinders up all the way and leaving more material left on the sleeve when compared to using a full .5mm over piston. The new piston came with rings and locks so you will only need to purchase 6 new locks and rings for the remaining three. They can be purchased off of JE site for less than $100. I would have used these in my next build but I decided to go larger since my block will be sleeved. I took pictures of the front and back sides of the used ones. You be the judge of the condition of them, I have tried to be as honest as possible about it. I'm looking to get $200 shipped for them. I paid $150 for the new piston so I believe that this is a pretty fair deal. I accept paypal for payment.
 

Attachments

  • 100_0397.JPG
    100_0397.JPG
    374.6 KB · Views: 232
  • 100_0398.JPG
    100_0398.JPG
    353.9 KB · Views: 220
  • 100_0399.JPG
    100_0399.JPG
    392.5 KB · Views: 206
  • 100_0400.JPG
    100_0400.JPG
    404.1 KB · Views: 248
  • 100_0401.JPG
    100_0401.JPG
    419.8 KB · Views: 228
  • 100_0406.JPG
    100_0406.JPG
    383.3 KB · Views: 207
  • 100_0405.JPG
    100_0405.JPG
    354.4 KB · Views: 219
  • 100_0404.JPG
    100_0404.JPG
    370.2 KB · Views: 224
  • 100_0403.JPG
    100_0403.JPG
    433.4 KB · Views: 233
  • 100_0402.JPG
    100_0402.JPG
    367.8 KB · Views: 207
Next thing up for sale is a b series vtec Ferrea 5000 series standard size valve set. These valves have 3600 miles on them and are in good condition. I decided to go to an oversized setup with my head so I have no use for these anymore. I just realized that two of the intake valves are missing; apparently the machine shop didnt get all of them back to me. So you would need to purchase two intake valves to have a complete set. I believe they go for about $20 a piece and can be purchased through any Ferrea dealer. I paid somewhere around $250 for these new. I'm looking to get $80 shipped or best offer.
 

Attachments

  • 100_0410.JPG
    100_0410.JPG
    361.7 KB · Views: 197
  • 100_0409.JPG
    100_0409.JPG
    379.9 KB · Views: 222
  • 100_0408.JPG
    100_0408.JPG
    417.5 KB · Views: 222
  • 100_0407.JPG
    100_0407.JPG
    384.1 KB · Views: 222
I have a set of RC saturated injectors for sale as well. They are 750cc and are part number SH4-750. These injectors have about 2000 miles on them and were purchased new for $320. Only the injectors are included, I havent pulled them out of the manifold yet. I would like to get $175 shipped for them. I upgrade to 1000cc injectors for my new build.
 

Attachments

  • 100_0411.JPG
    100_0411.JPG
    974 KB · Views: 217
  • 100_0412.JPG
    100_0412.JPG
    282 KB · Views: 201
Next up is a factory b16 intake manifold off a 2000 si. I cleaned up some of the casting in the runners as you can see from the pictures. This manifold will come bare with no sensors or any other parts seen in the pictures. I'm looking for $45 shipped or best offer.
 

Attachments

  • 100_0414.JPG
    100_0414.JPG
    313.6 KB · Views: 209
  • 100_0413.JPG
    100_0413.JPG
    426.6 KB · Views: 209
  • 100_0411.JPG
    100_0411.JPG
    974 KB · Views: 204
Last thing up for sale is a treadstone intercooler that is 36 inches end tank to end tank, 10.5 inches tall, and 3.5 inches wide. The inlet and outlet are 3 inches. There is one small dent toward the bottom which can be seen in the picture. I received it this way when I bought it new but didnt want to go through the hassle of returning it. It doesnt leak or have any other known problems. I'm looking to get $180 shipped or best offer.
 

Attachments

  • 100_0415.JPG
    100_0415.JPG
    927.2 KB · Views: 234
  • 100_0416.JPG
    100_0416.JPG
    762 KB · Views: 205
  • 100_0417.JPG
    100_0417.JPG
    464.4 KB · Views: 210
  • 100_0418.JPG
    100_0418.JPG
    417.8 KB · Views: 200
are the injectors the honda rc ones? or are the the regular rc. im not looking to change my plugs for the injectors
 
As long as you have obd1 honda injector plugs they are plug and play.
 
Back
Top