It is time to sell the 2 yr project EK. The car is a black 97 coupe. Originally an HX (Better insurance) MAny many things have been changed. Here is everything I can remember
ENGINE
B20b block GE sleeved bored to 85mm
Wiseco 11.5:1 cr with ARP rod bolts
b16 head with civic type r cams, springs...
I tried jumping the harnesss to pull codes for a 95 HB si with stock harness, p28 ecu with hondata s100. I jumped the wire and the srs light just blinks forever no long blinks, no pauses or anything. It just blinks fast indefinitely. Any ideas what i am doing wrong.
I jumped the blue connector...
My friend asked me to help him fix his high idle on his swap. He swapped a obd2b gsr into his obd1 95 civic si. He has a high idle at 2500. I just needed some troubleshooting help for this swap into this car. Are there plugs that are the same that can be plugged in the wrong plugs and cause a...
I am putting an OBD2b GSR into a 95 hatch si. Let me know if I am missing anything. Here is what I am thinking:
I can drop the engine in, but I need to swap the distrbutor and alternator for ones that are OBD1. Of course I have to get mounts, axles etc.
Can I use the 95 SI harness? What do I...
I got a complete OBD2b GSR that came from a 99-00 civic SI.
I am putting it in a 92-95 and converting it into a OBD1.
Are the only things I need to convert are the alternator and distributor?
Also are the distributors between OBD2b and a OBD1 physically different, because when I try to put...
Here is the problem.
My b20 vtec won't start. Here is the story and symptoms as well as what I have done so far.
It drove, started and idled fine up till now. I took a three hour trip in 70-80 degree wheather. About halfway I noticed a tiny tiny tiny drop of fuel leakage from the gage on my AEM...
Here is the setup
B20b block GE sleeved bored to 85mm
b16 head with type r internals
JDM type r header
Greddy exhaust
str 68mm tb and cam gears
injen CAI
AEBS intake manifold
AEM fuel rain and regulator
hondatas s100
and it still has a cat on it.
Setups
B20b block GE sleeved bored to 85mm
b16 head with type r internals
JDM type r header
Greddy exhaust
str 68mm tb and cam gears
injen CAI
AEBS intake manifold
AEM fuel rain and regulator
hondatas s100
Here are the numbers
235 hp at 7500 rpm
177.8 ft-lbs torque at 6000 rpm
Pictures...
Hi guys,
I have heard great things about skunk2 short shifters. I was wondering the following:
I have a 97 civic ek coupe with a b20 w b16 vtec head. Which short shifter do i get for what year and if possible a part number. I had a short shifter on my stock d16 (HX), but it did not work with my...
Will a B16A2 OBD2 Throttle Body bolt up to a D16 92-95 OBD1 Si motor (sorry don't know the engine code)?
If so what do I need?
Does the OBD matter?
The throttle body is bare? Can I use his sensors?
Thanks
Khai
What is the cause of spinning a bearing in the block?
How do you know if you have done it, while you are driving?
If I disassemble my block will I be able to tell if my bearings are spun?
How much do the bearings cost to replace?
Khai
Ok I have decided to boost. Here is my current setup. It is running and I am jsut not satisfied with the setup.
B20b block 12:1 cr pistons
SI tranny
B16 head
AEBS intake manifold
STR 68mm tb
3" CAI
ITR Header
Greddy Evo Exhuast
CTR cams, valvesprings
AEM fpr
255 lph fuel pump
I will be...
My friend has a bone stock 99/00 civic 4 dr LX (economy car). She has had the car for a few years. It has 50,000 miles. All of a sudden this morning it didn't start. When she turned the key it cranked but didn't turn over. Her radio comes on like normal. Any ideas what it could be? Or what it is...
I had the 13.5:1 compression pistons in a swap i just bought. I can not tune the motor with this compression and pump gas so I will be taking the pistons out and putting in lower cr pistons. I will be running ctr cams.I heard that higher compression does not necessarily mean more power. It...
Hi guys I did a compression check and got 280 in each cylinder, about what compression ration would that yield? If you don't know can you tell me about what compression ratios you have with what pistions.
ie JE 12:1 = 240 compression
etc.
Thanks
Khai
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.