Search results for query: *

So every time I press my clutch in to stop at a stop light my engine RPMs drop down to 200 or the car dies all together. It only happened after the car warms up and it starts right up after it dies. I've replaced the Idle control valve with a known good one and have played with the idle screw to...

Car starts, and runs great. However, at random intervals the tach will jump up and down and my car starts to sputter. It will also do it when I start from a dead stop. The car will sputter and choke itself out, but I am able to crank it over and start it again. Does anyone have any ideas? I have...

I am new to the area and I am trying to find some good shops to check out and maybe get some parts. Anyone know of any good places????

Delete

SO I switched my rex from obd0 to obd1. I have a obd1 dizzy and a chipped p28 with a adapter harness. I hooked everything up and I dont get any spark. I believe I am getting fuel, because I can smell it. I rechecked my wiring on my dizzy and its correct. I even swapped the two white wires...

Anyone have issues with eagle h-beams in a d16a6? I noticed that they don't have an oil galley for the wrist pins and was wondering if this was a big deal.

I found a set of sway bars for an ef and I was wondering if the sway bars are the same for the civic and the crx? I would think so, but I am trying to be sure. Thanks

What is the differance between the d15z1 vtec-e head compaired to the d16z6 or 8y heads? Is it the cam or or port design?

Can you install 94+ integra front brakes into a crx? I can get them for dirt cheap and i want to know if it is possible to do it before i get them.

My buddy has a 93 si hatch with the d16z6 engine. He let me drive it and i hit vtec at 5200rpm. After the first time all the engine does is bobbles at 5500rpm like it is hitting a rev limiter. I thought maybe it was an oil issue so i checked the oil level, and the level was good. I then...

I am really interested in learning how to use turboedit. Does anyone know of a write up that explains the basics of using it. I have been using search, but haven't found anything useful.

will they fit into a 90 crx? i can get the full assemblies, brake master cylinder, and brake booster. I just need to know if they will work or not. thanks.

Can you put ls rods into a d16a6 block? If you can what do you need to to make it work?

Were can i go to find a complete b16a swap for my crx. I know of 2 websites i can go but i was wondering if any one can tell me of any good places to buy the swap. If it matters, I'm on the west coast.

I have a turbo system going in my car and i want to play it safe. the waste gate is fully open at 15psi. I only want to run like 4psi when i first get it in. What do i do to make it so i can run only 4psi. I know that a boost controller is good for uping the boost, but what about keeping it down?

I have the oppertunity to get a zc sohc cam for my d16a6. I am making sure that the zc cam is a little more aggresive than the a6. It is right?

I am building and all moter d16ad mini me for a friend along with turboing my own si. I have been concentrating to much on the turbo build than i have on the all motor. has anyone done an all motor d16? Also what kind of gains could you see?

I am interested in purchasing p29 pistons out of a dohc zc engine. I am also interested in buying a sohc zc cam. Any have any of these that they are willing to get rid of.

I am doing a motor build for a friend of mine and i used a compression calculator to see what i could possibly go with. In the head gasket section there is a d16y8 gasket and a d16y8 2-layer gasket. WHERE do i find the 2 layer gasket. The auto parts places are stumped. Any help would be great.

I wanted to know if anyone has done a all motor d16. I was thinking about something along the lines of a d16a6 block, z6 head, and zc pistons. The head was is going to be built (I.E. valves, springs, titanium retainers, comp cam, P&P, and 3 angle valve job.) trying to do a high compression...