Search results for query: *

Ok, i have a p75 head, Fresh valve job, Supertech valve springs, Titanium retainers, Exospeed stage 3 cams, stock cam gears, no valve cover (unless i can find one laying around) 450 bux, I can also have the head street/strip ported/polished for an additional 100. What im looking for... 81mm...

Ok, ive really been looking into ITB's for my ls/v crx. My buddy has a set of 38mm ITBs off of a yamaha. I know about all the work involved with setup and tuning... Im not scurred of that. I was just wondering if that is big enough to support atleast 300whp. Thanks.

Ok, me and my buddy are building a drag 95 civic coupe. There is a F23a1 in it right now, and we have a Nos v8 wet kit on it. We have it jetted according to the fuel pressure with the chart for the kit. We are running a 51 nitrous and a 34 fuel jet. Im just curious what size hp shot that is. It...

Ok, i just finished my LsVtec, and i didnt want to Tee my oil pressure switch off. I just want to get rid of it. Yeah that may sound like a dumb idea, but when have you realy seen the light on other than when your engine was already screwed? Anyway, does it affect the ecu when its off, and is...

Ok, my setup... B18a1 block p30 pistons Comp stage 2 cams P/P head shaved 12 thou B16 oil and water pumps Stock cam gears 12:1 C/R And my problem. I fired the engine up, set my ignition timing to stock. I know my head has been shaved so my cam timing is 1 degree retarded. The engine will idle...

Ok im just about to finish my Lsvtec, and i pulled out a hacked d16a6 harness. I have a Ls harness out of a 90 integra, and i was curious if it will plug in and pinout the same on my 89 crx Si. I just want to start fresh on my harness. I spent all this time and money, i dont want to have my...

Ok i threw a rod on my b16, and my piston ended up getting damaged. Im building a LsVtec right now, so i need one piston to match the one i blew, a pr3. I dont have much money, and i need all these parts overnight same day, yesterday, whatever. Im located in 44107, cleveland ohio. if your...

Ok, im building an lsvtec rigt now, and the head i have has already been bored for ls dowls, and tapped for the lsvtec oil supply. So, i dont need to buy a kit. I was just wondering what head gasket should i use, the LS or the GSR? And what exactly needs bored, the spot where the dowl pins go...

Ok, i have a completley dissasembled B18b1 block that has been hot tanked, checked and honed, with a new set of ACL bearings. all pistons/rods/crank/hardware is there (i belive). Its just a short block, however in realy good condition/extremly clean 250 plus shipping I also have a 95 GSR head...

ok, so i just got a rex that was pre-swapped. its not running right, so i checked the ecu for codes. its throwing codes 1 and 2, primary and secondary o2 sensor codes. The car has a dc header on it, and only has provisions for one 02. I am going to be chipping the rex, and want to disable the...

ok, i just picked up a b16 swapped 89 crx, runs great, idles fine, etc. It has a problem tho, and its kinda fishy. According to the vafc, at about 10-15% throttle and around 1500 rpm, the engine cuts out. like it just ran out of gas or is running out of gas, untill i let off the throttle and...

Ok, willing to sell shell or whole. This car is not complete. its a project. However it is almost done. I have hundereds of hours into this car, but i could use some money, because my daily is about to die. this would make a great winter project Ok down to the nitty gritty... D15z1 with...

Ok, i have a block here that was preped for a build. Its a b18b1 ls engine. Everything is here. I just ran across a car i want, and need the money from this engine to pick it up. The block has been tanked and honed, there was 60k on it when pulled All the pistons are pulled, and individualy...

Ok, here is the deal. I found a complete LS motor, and the dude threw in an incomplete GSR head for real cheap. I picked it up. I want to find the rest of the GSR parts. I guess its pretty common that people pull off the stupid stuff that you need to complete the head all the time (i see it on...

I just found out i have a bad upper right ball joint (passanger) and i need a new one. So.. I am willing to trade a set of 94-01 teg uppers in great shape for the passanger side i need. Also willing to trade one for one, or i will sell both for the cost of a new one. (whatever that may be) Let...

Ok, I am finishing up my wiring harness right now, and im working on the dizzy plugs. I converted the car to obd1 with a p28 and jumper harness. Im using the obd1 dizzy in this swap, and have it all wired up except for the solid white wires on the plug. There are two coming out of the harness...

Ok, i know that my EG can have the fuel pump changed from inside the car, but im not sure with the EF. I see the sending unit, but i do not see a portal for the fuel pump. (warp speed captain) I am asking before i drop the tank, because i once did a fuel pump on a dodge stealth, and i couldnt...

Ok, so here is the deal. I am settin up my turbo on my "Project-EF" The manifold i have for the turbo shoves the turbo all the way to the core support. No room for the full radiator. No big deal i have an EG radiator laying around. So i set the radiator in, and i have to modify the mounts, no...

Ok, im running out of money, and thats bad. I have one slightly used act street clutch. Its very nice, and gripped very hard. I can get pics, but would like to get 60 shipped for it. Thanks.

Im building a turbod d15z1 mini me on my 89 hatch, and am going to run a P28. Im using a d15z1 block with a d16z6 head. If anyone has one, or a very detailed how to on how to make one, hit me up. Thanks.