Which mounts do I need to install my d16a1 1.6 dohc 89 teg motor into my 91 crx dx. PLEASE HELP ME...I have been told to use b-series mounts or stock 89 teg mounts, well you tell me. Someone said to use hasport b-series mounts but I was wondering if they were the same as the stock b-series mounts?
D16A1 INTO 91' CRX DX
- Thread starter b18c14
- Start date
- Replies 12
- Views 7K
We may earn a small commission from affiliate links and paid advertisements. Terms
brian11to1
Senior Member
use stock d series mounts from either the DX or Si...
The motor is in and the angle of the motor is not right and the motor is to high on the drivers side, Using the stock dx mounts.
D16A1 does not bolt into 2nd gen CRX without fabricating mounts for it - there are no aftermarket mount kits for this swap - on the driver's side end of the engine, the D16A1 mount is located on the front of the block - the 2nd gen CRX uses mount that comes off end of block at middle - which transmission are you trying to use? Integra transmission mounts will not fit CRX chassis and CRX transmission doesn't bolt to the block correctly - in other words, the D16A1 is not a good swap in a 2g CRX
werd
how the fuck did you get it to bolt in?
D16A1 bolts into first gen crx...
2nd gen has diffrent mounting locations...
Motor drops right in minus the mount problem. The drivers side mount holds the motor up to high, reason being (just found out from buddy that owns a shop) the Si 2g rex came with the option of a jdm dohc, so the motor (d16-a1 or a8 or a9) has both front studs and side drilled mounting points. SO EVERYONE, IF YOU WOULD LIKE TO DO THIS SWAP HERE IS YOUR ANSWER. DRUM ROLL PLEASE... A set of stock Si mounts will bolt your dohc d-series block into your 2g rex.
If anyone other than myself has completed this swap I would love to hear about it.
If anyone other than myself has completed this swap I would love to hear about it.
didn;t second gen crx's have B16's as an option in jdm land?
91 crx sir
and 90-91 civic sir had b16's
dohc b > dohc d
91 crx sir
and 90-91 civic sir had b16's
dohc b > dohc d
i for one am not buying it - here is a picture of the D16A1 block - maybe you could point out on the picture where the stock 2nd gen Si mount bolts to the block - by the way, see the studs sticking out on the left side - that is where the A1 mounts
No, the Si and the hf mounts are the same. Call the parts house and ask for the part numbers on both sets, I called today.
The top bolt hole on the mount is 3/4 of an inch to the bottom left of the ex. cam gear and the other is located about four inches lower than the first. I'll take a digi of it with the mount attached to the block along with a shot of the block code and post it a.s.a.p.Quoted post[/post]]
i for one am not buying it - here is a picture of the D16A1 block - maybe you could point out on the picture where the stock 2nd gen Si mount bolts to the block - by the way, see the studs sticking out on the left side - that is where the A1 mounts
Yes sir that is correct, also the d16y8 sohc was an option in jdm land (in a rex)
I am sorry about the mix up, I don't need the mount I need the perch that bolts to the mount.
blackice90HB
Senior Member
d16y8 is the SOHC from the newer civics, the 130hp motor I belive. i dont feel like looking it up or else I would, but Im sure thats the motor from the EK's Dx or ex or whatever one. The motor your thinking about is the D16A8/A9, the "dohc zc" motors. they were avalible in Euro markets too. The SiR's were OBD0 B16's tho. ask jlicrx, thats the f-ing ZC genious.
