Recent content by Buff_Hatch

k, here is what it looks like. as you can see, it is hitting the rear side of the mounting bracket , closest to the firewall. these are new mounts but because the bolts on the REAR mount was loose, it caused it to move. So, I don't want to buy new ones, just what can I put inbetween...

Have a 1990 Hatch with the B-series. All 3 Mounts are new, and a stiffer Urethane than stock. The problem is the Driver's side mount is "walking" off the steel tube where the bolt slides into and the mount makes contact with the metal part of the mount attached to the frame. Is there any...

I see the Innovative Front Mount. Looks good, I will have to fabricate the bracket to the bar I currently have.... however. The mounts I have are Innovative, the 75a rubber, which you can feel more than the Standard 60a.

It is an item off of e-bay, search civic traction bar.... not sure of the brand

I know on the D series I removed, there was a "dogbone" type in the front. On the 1992-95, some of them have 5 mounts. I don't mind fabricating the mounting bracket to the traction bar, but need to find a suitable mount for the front.

Have a 1991 Hatch with the B16 swap and new slightly stiffer than stock motor mounts, don't remember which ones but they make the dash shake a bit more than normal. I have the traction control bar on the front. However, when I take off from a stop, the torque on that thing shakes the engine...

Have a B16A JDM with Type R head in a 90 hatch. Has been running great for about a year and now is throwing a code - 2 long blinks and 3 quick blinks, so I think that means 23.. when I looked it up it refers to the Knock Sensor... I have tried reseting the ECU and it will still pop up after a...

Help!!

Have a 1990 Hatch with a B16A swap and there is a lot of vibration from the rear motor mount bracket [firewall area] riding on the the frame. I took a look at this: https://hondaswap.com/hybrid-eg-ek-dc/motor-mount-install-sequence-help-88881/ and wondered if I have the wrong bracket for...

Thanks for the reply, I did find the cause, a new wire was run from the O2 sensor to C2 on the wiring harness. No, this was done by the previous owner. Anyway, the car runs great now, no codes. Even though the O2 sensor is not hooked up, it does not through a code for it. I suspect that the...

Thanks, I will keep that information in mind. I actually found the problem with the distr, the retard that had the car before me wired the O2 wire to C2, which is for the CYL #1.. I reconnected and it runs great! So, I won't have to purchase a new dist. :D Thanks for the help!

I am having problems with the ECU throwing a Code 9 - the CYL #1 sensor and if I am correct, it is in the ODB0 dizzy and would have to be replaced as a unit unless I can find another cause or cure.. So if I have to replace the dizzy, then it was suggested just to go to ODB1 [ wiring harness...

With the swap to B16A I am using the PR3 ECU. .. If I go to the P28 or P30, do I have to do rewiring? Any kits available? Any help appreciated,,, new to the ECU upgrades--THANKS!

Have a 90 Civic Si Hatch with the B16A engine swap.... It seems like it should have more power, then I noticed the Code 9 error.. It is the #1 Cyl Pos... any way to test this sensor???

Yes, mostly cyl head work - 11:1 compr, ported exh, ported int, 3-way valve job, 272 degree cam... etc. 4-2-1 header... 2" exhaust all the way back... Still using 240cc injectors though...