so like the title says obd0 b16 dizzy. part number is TD22u. i'm asking 150 to your door. part was purchased new and had it on my car for a lil over a week, till my obd1 dizzy came in.
ok if its not in the right spot then move it..... i have a 90 integra with a jdm b16 sir2(xsi). and i cant seem to clear the codes off. here are the things i have done: disconected the whole battery for like a lil over a minute,pulled the 10a fuse in the under the hood fuse box were it says ecu...
ok so i have a b16a sir 2, and can get and ITR manifold for 205 plus shipping. will it bolt right up and all lines go into place(smog). and if so should i go with this or shell out the extra dough for a skunk2. and if i do shell out the extra dough should i get the old version skunk 2 manifold...
ok i swaped in a obd-1 b16 into my DA wich is or was obd-0(converted to obd-1 now) so i'm throwin only the IACV code after clearing the other codes and was wondering how everyone that has obd-0 cars wired in there IACV.
ok so there are 2 sensors on the back of my obd-1 b16 and want to know exactly wat they are. one is a 1 prong sensor sticking out and the other is a black plug type sensor(possible knock sensor?) and also wondering were my thermostat sensor is located. some one said in the thermo housing and...
ok so i jus got done doin the swap and i'm throwing a few codes but will be cleared in a few days, anyhow we took it for a lil test drive start it up and pull it out and get into a lil bit and vtec cracks. which usually doesnt happen unles the engine has proper oil pressure, and the car usaully...
they are for my obd1 b16, code 9 is the cyp sensor and is in the distributor so i might have to buy a new distributor to fix that. code 14 is the IACV and was wondering how everyone else has wired for that on there obd0-obd1 swaps. and code 20 is for a elictrical load detector, now wat the hell...
ok so on the resistor box of the obd-0 car there is a green plug that goes to it and on one side there is 4 red/black wires and a yellow wire. then on the other side were it goes into the resistor box there are i think 4 black wires. how do u wire this up because i wired the 4 red/black wires to...
ok so jus got all the obd-1 things hooked up today for the motor. took out the resistor box and sautered the wires together. hooked up the 4 wire o2 sensor and hooked up the obd-1 dizzy. so with the ls ecu in the car ran good jus wouldnt hold idle. then now with all the new things done and the...
jus curious if it will fit(prolly will but jus want to chek). i have a b16a2 sir2 obd-1 motor in my DA and want to make sure the skunk2 manifold will fit before i buy it. simple yes or no will suffice.
thanx
ok i have a 90 integra gs and i've swaped in a obd-1 b16a and i'm useing a frogs jumper harness. wat i need is a diagram of were every thing is wired to. specifically the oil pressure return. so if someone can link me to a site to help or anything let me know thanx. and i did a seach and found...
ok heres the situation..... swap in an obd-1 xsi b16 into my 90 2gen. wired in the vtec and all that and wired in the obd-1 distributor to my stock wiring harness and bought a obd-0 to obd-1 conversion harness for the pr3 ecu. so here we go it had a fuel rail gasket leak but the car started but...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.