Search results for query: *

I have a stock exhaust on my ex motor ... on 1 end of the a-pipe are 2 flange rings that go to the exhaust mani; I need 1 on the other side of the a-pipe that goes to the catalyst, a 1 gasket/donut. Honda says this piece is either- p/n 18229-s01-x01 (45 mm In.diameter x 58 mm outer dia.) or...

I swapped a d16y8 in place of the d16y7 on my 99 civic. Come to find out motor's originally an automatic, yet the swap was ok ... everything bolted fine to the ecu (p2p for 5speed tranny) problems- I have 2 CEL codes - 2ndary o2sensor circuit & IAC circuit. I think if I remove it & clean it...

I swapped a d16y8 in place of the d16y7 on my 99 civic. Come to find out motor's originally an automatic, yet the swap was ok ... everything bolted fine to the ecu (p2p for 5speed tranny) problems- I have 2 CEL codes - 2ndary o2sensor circuit & IAC circuit. My o2 wiring doesn't seem to work...

1st of all, I have no ability to post a picture .. Sorry, I know this would make it 10x easier. I'm putting in a 99 d16y8 into my DX. It was delivered with the wrong exhaust manifold (not attached or bolted to the head). I should have gotten a cast iron manifold with a heat shield & an o2...

I know to do my 99 Civic clutch I need 'star' sockets to get at the pressure plate & flywheel. I could buy the tools from Honda, but would rather rent (?) or buy elsewhere. So, please, give me specifics: What are the part numbers, where can I get them, how much can I expect to pay ...?

Background- for reasons of my own, I'm redoing the engine/5spd on my Civic DX .. it's soon to have an EX driveline. I've talked to a few shops, read through many sources, & talked to ppl .. only CARB legal parts will pass smog. But, I'm being told, if I have noticeable changes from stock, no...

please give me a link for a helms manual online ... 1999 civic I had it at one time, but my 'puter died. Thx

I need both before & after cat o2 sensors What's a good price? What's a good brand? What should I avoid?

pleaz, how many lbs. is a D-series 5spd transmission?

Sorry, I know this is actually a hybrid question, but I seem to get little response in that forum. Anyway.... I'm switching from a d16y7 to d16y8 motor. I believe the exhaust won't line up to the new manifold ... & buying a cat-bac system only solves half my problem. I've gotten a few quotes...

For budget reasons (& for VTEC), I'm replacing my d16y7 with a d16Y8 motor & 5speed. So, a simpleton question.....? Can I use a p2p from an automatic transmission Civic ?

So anyone have an idea of what makes for good weight savings? I know smaller alloy wheels are on the list. What's the weight savings with a carbon hood .. fiberglass? ...rear deck (or hatch)? ...pwr steering & a/c are the 1st to go, then interior .. anything besides that?

I need to switch my D16Y7 to a Y8. From my knowledge and experience, when it comes to an overhaul on the motor, Honda motor & trannys are often treated as one unit. But if my tranny's fine but motor's bad, I'd wanna just disconnect the motor & pull it. I see it as less hassle with linkage &...

my civic's overheating more often. At this time, I'm left with the cheapest route if I want VTEC ... D16Y8 motor. I'm researching, though have lotsa questions. 1Are junkyards a reliable source for a motor or where else should I look? 2What's involved in wiring & ecu ... are these tough to do...

I used to own a vintage (ie. old) domestic (GM) muscle car & actually snapped the ball joints a few times while driving aggressively. Questions - Anyone ever broken an A-arm or ball joint on a Civic? I'm told the balljoint's unserviceable & meant to be replaced as-a-whole .... so, any idea what...

I posted in another forum, maybe there's no answer ... My d16Y7 has 150k. It needs a head gasket cause it overheats idling/sitting 5minutes; a 3rd/replacement of the cat - frequently blows p0420, catalytic below threshold .... I don't have the place or time for it, so I'd prefer to pay someone...

150k & I'm maintaining my gutless wonder ... What Honda/Acura models use the micron air filter for the heat & a/c? Is it pretty easy to replace?

The plastic wheel covers on 14" steel wheel rims are shot, and I'm just gonna run the rims ... to cover the wheel hub nut/pin, couldn't I use the letter H Honda wheel hub covers found on the 13" series rims? 99 civic

I have a 99civic. The d16Y7 is starting to show its 150k ... typical ... needs a head gasket cause it overheats idling/sitting 5minutes; a 3rd/replacement of the cat - frequently blows p0420, catalytic below threshold .... I'd like to save the hassle of a new car and drop a b18b1 motor/trans...