Search results for query: *

This is off of my Y8 swap and for some reason there is an obd1 Z6 Intake manifold on there with this line. On my Z6 the line goes where I have pointed out, but the Y8 as you can see already has a hose going from the FITV to under the intake manifold. Where can I direct this coolant line or...

Just did the y8 swap back in my 98 ex. It starts up just fine but has an idle problem. It surges up and down really fast. It has the IAC code 14. I'm using the P2P ECU and I also have an OBD2 P72 I've been trying to see if it runs any better. I noticed it's a complete y8 swap with obd2...

Are the 92-95 and 96-00 rear T brackets the same? I have a D16y8 im putting back in my 97 ex coupe and I can't get the drivers side mount to line up, I'm using the 92-95 T bracket but if they're different then that must be the prob.

I have a wire on my sohc obd2 harness for the knock sensor I thought only B series had that but I must be mistaken. There is no sensor on the back of the block for it though so I will definately have to get it somewhere right? otherwise it will throw a code? One other ? are the rear...

Will I be able to fit a decent brake upgrade kit on my eg hatch if i went with 15x6.5s? If not I'll have to go with 16s, but I like 15s because I was going to go with the bf goodrich drag radials and I dont see them making 16" tires i only see Nitto and mickey thompsons in 16s.

I have a 94 VX and with front discs, rear drums. Swapping in a turbo GSR and I am looking for a big brake kit that will fit inside of a 16x7" wheel. I know a lot of people just do the gsr disc conversion or even the ex/si rear disc conversion but wouldnt that be a waste of money since I am...

Im deciding on suspension for my hatch and don't know the first thing about it, it will be putting down 450 whp not going to be a daily driver, mostly track and strip. I've already got traction bars, urethane bushings sway bars and strut bars. I'm thinking about preloading, probably slammed...

Selling 1994 jdm GSR tranny w/ factory LSD 60k miles since rebuild had new syncros installed shifts great absolutely no grinds. Asking $800 OBO Need non LSD tranny so Quaife LSD will fit trades for non LSD GSR or B16 tranny will be considered, of course with some money up front Just...

I thought all YS1s were cable but apparently mines hydro, stamped YSK in a circle and beside it the number 1. It came on my JDM B18C swap, so I'm thinking someone may have combined 2 cases here one with the hydro connection and the shell part off of a YS1. IS that possible? When I first got...

Does anyone know any good info on doing timing belts on ZCs? Ive searched and searched every link I click on tells me to do something different, I've adjusted the timing on this ZC like 10 times and still its not acting right, only Codes I have are IAT and coolant temp sensors. It starts up idle...

Local shop told me that since my GSR tranny already came with a stock LSD being JDM the quaife LSD wouldnt fit on the ring gear bolts, which is doesnt. They said I should get a USDM final drive from a GSR tranny and then the ring gear bolts will match up is this true?

Had to switch transmissions in my 89 hatch, both transmissions have gold stamps L3-1 making them both 88/89 and both are PL3-3000 making them SI correct? One has 20 splines and one has 21 why is that? my clutch is brand new on my 89 SI tranny that I pulled out but its 20 spline and wont fit on...

Bought a 93 JDM GSR swap, B18C stamped on the engine why is that instead of B17?? Anyway thats not the worst of my problems I go to buy a 94-01 Integra GSR Quaife LSD to replace the stock LSD and it wont fit its too small and wide. My tranny is hydro, all stamps have been removed and its...

I have a 93 jdm GSR with a stamp B18C weird cuz I thought they were considered B17s the guy at the jdm motorshop said that when I go to buy parts for it its considered a 94 over here. Well the 94-01 LSD is different I need the 92-93 one. As far as the clutch assembly will a 94-01 clutch work...

OK I finally finished wiring up today and after triple checking all wiring to make sure it's all right since the first article I read on how-to was completely opposite of what needed to be done. I can only think it maybe an injector problem they have been sitting around for about a year or...

Well it all started in my CRX DX when a valve seal went bad draining oil out of the exhaust port. I pulled the head and I had an SI head laying around so I swapped that in instead of replacing the valve seals, probably a bad move. I kept my DPFI intake manifold on and at first idle was really...

Im installing a Quaife LSD into my GSR tranny, does anyone know the torque specs on the ring gear bolts?

92-95 D series Stage 1 Exedy clutch $150 OBO GSR (black) valve cover - $50 OBO 92-95 Honda Civic comeplete energy suspension bushing kit - $100 OBO 92-95 Civic Hi-flow catalytic converter - $35 OBO 92-96 Prelude full front suspension struts/N1 coilovers/ hubs/rotors/everything - $200 OBO...

Whats the difference between the two... other than the PG7 is an integra ECU and PM7 is the ZC ECU. I have a JDM ZC engine and am running a PG7 is this fine I do have 4 cel codes on Codes 6 - Coolant temp, 7 - throttle angle, 9 - No1 cylinder position, and 10 - air intake temp If I were to...

OBD2A to OBD1 Conversion Harness Fits 1996-1999 Acura Integra 1996-1998 Honda Civic 1996-2001 Honda Prelude 1996-1997 Honda Accord $50 plus shipping Stage 1 Exedy clutch for D16 M/T $150 plus shipping Tein S tech springs 92-95 honda civic $75 plus shipping Energy Suspension Hyperflex...