Search results for query: *

Don't know if this is the right forum or not so excuse me if it is in the wrong place. "The change in horsepower due to the change in compression ratio is relative but not directly proportional." The way I understand this is that a increase from 8:1 to 9:1 would increase horsepower while...

I don't know if this is normal or not but I really never payed much attention to the stcok ecu in the 91 crx. I removed the carpet and noticed when the car runs the red light never stops blinking. I was looking for the codes and all that but I think maybe it is a general failure or something...

Wanted to know if anybody had some good information on what colors do a better job of hiding flaws in the body. I am not talking about huge dents and scratches but normal everyday wear and tear defects. I was considering repainting my car to the original black but everybody tells me that the...

I forgot that I had this thing until I was looking for some other stuff tonight in the garage. I wanted to put it on when I was going to try to do the mini-me swap. Can I use any of this on my 91 crx si that is still stock just in case something ever breaks or whatever. Thanks and I honestly...

I looked all over this place they call a town for some rattle can paint. I was hoping to spray my wheels but that color can't be found around here. They have plenty of camo and bright orange lol. Anybody seen this paint anywhere?

Well 9 months later my son has been born and everything has settled down a great bit and it is time to redo the crx. I was going to do a mini-me swap but have put that on hold since I need to start driving the car back and forth to work daily. The oil compression rings are pretty much shot and...

I have a '91 crx si D16A6. It is pretty much stock except for a header, intake and tannabe exhaust system. Maybe I have been screwing with the car too much and I have lost focus trying to trouble shoot everything but here we go..... -Car fires up great. -When you start the car and let it set...

Finally got a header and a Tanabe exhaust system for my car. The current converter on it is about old as dirt and I was going to get another one to replace it because it has a few small holes in it anyways. All I have is a D series SOHc engine and was wondering if it is worth it to pick up a...

Another noob question that the the tech book has failed me on once again. I was looking in the repair manual to try to adjust the idle a bit and it said on '88 crx si (my car is a 88)and later models it is located near the throttle body somewhere near the accelerator cable connection. Well I...

Just wanted to make sure that this info is factual for the D16A6. Displacement : 1590 cm3 Bore and Stroke : 75 mm X 90 mm Compression : 9.6:1 Power : 110 hp @ 6000 rpm & 100 ft·lbf @ 5000 rpm Valvetrain : SOHC Fuel Control : OBD-0 Multi-point PGM-FI Head Code : PM3Also a couple of other things...

I am getting ready to get my car painted and was looking for a quality rubber kit for the thing. The guy said he would install them if I could round a set up. The ones he said he can get are not that great. I have looked everywhere that I know for a set of window,lights.door etc kit and cant...

Just got my engine back together and noticed I have no mass air flow sensor. Any particular one better then the other? I have only minor mods but my head has bigger valves in it and just got redone as well as a new head gasket,timing belt, alternator,starter,rear main seal, water pump etc. I...

OK I got a '88 CRX and it is time for a new water pump. It is making a horrible noise. I went out and got a OEM replacement and started the project. I had to remove the valve cover to get the top timing belt cover off and once I got that done the damn alternator belt was in the way of my tools...

I got a '88 crx SI and just bought a header for it and plan on installing it this weekend. I also want to replace everything from the header back. I was looking for an exhaust that has a deeper tone to it rather then one that sounds like a monkey farting in a water pipe. Thanks

I have a 88 CRX SI and I was hoping to swap motors and replace the thing with a B16A2 series. I have read a bunch of info on the net and have come to the conclusion that I am confused. After reading pages and pages of articles some of them often debunk one another. I am not trying to get all...