Search results for query: *

I have a JDM ZC and I bought the L3 LSD tranny to go with the engine. They will be going into my '88 Civic LX, I was wondering if I will need new half shafts or anything like that? I was told that I might need 89 Integra axles but I don't really know. Thanks for the help.

I have an '87 JDM ZC engine that's going in an '88 Civic, I am donig a full rebuild of this engine and I bought some Eagle H-beam rods, part #CRS5394H3D, these are for the ZC, or so I was told, and I put them in and tightened one down on the crank, but when I tried to rotate the crank the rod...

I have a block with some rust inside so I am going to bore it a little. My machinist says that if I can get pistons that are 10 over it should be fine. Does anybody know somebody on the internet that sells over sized pistons for the D16Z6. What brand and what site? Also what would be the exact...

So you (atk724) think that it would just be easier to go to Nappa and order the ones for that engine? Would they have as good of a fit as the color coded ones from honda? So you think the rod bearings are going to be green? Thanks for the help.

I have a JDM ZC and I'm replacing the rods and pistons and the such and I obviously need to replace the rod bearings, but I'm unclear on how to tell what bearings I need. I'm pretty sure that I need bearings from the D16Z6 but I talked to a guy at a Honda dealership and he said that there is...

I am looking for some ARP head studs for my ZC. What do I need? I assume that I can just get some for an '89 integra, but where can I find them? If anybody has some for the ZC could you let me know where you got them, or an internet site that sells the ones that fit the ZC. The only ones that...

I have a JDM ZC and I am doing some pretty major renovations, such as new pistons, rods, rings, and the like, also while I have the engine torn apart I was thinking about getting the head ported and polished. It's pretty expensive but I want to know if it would be worth the money to do it or...

Does anybody know if any of the pulley kits from AEM will work with the JDM ZC? I was looking at the kit for the 88-91 CRX, #AEM-23-7009C. If this one fits please let me know, if not is there a kit out there that would fit. And what brand. Thanks

How about when I take apart the head. I plan to get it ported and polished so will I need any seals, gaskets, or anything like that before I put everything back together? If so, where would I get these, or from what engine will they be from? Thanks

I just got my ZC engine and I am starting to take it apart and build it up. I need a new throttle body and distributor. What throttle body should I get, I'm going to get a large aftermarket one, since I have to replace it anyway. I can just buy one for the 88-91 CRX Si right? What else should I...

I'm planning on builiding for nitrous. I'm going to be running a 75 shot of Zex through the ZC once built and in the car. I was thinking that I would like to turbocharge the engine, but that would be a long while off. So for right now it will be n/a and occaisional n2o use. The comprssion ratio...

If I was to get some arp headstuds, would I just get them for the d16z6, or for the USDM ZC? Also, what would the new sleeves get me? And where do you get sleeves, or would machine shop make them for me. I'm not quite sure what a blockgaurd is. Where can I order some new rod bearings from, can...

I'm just recently purchased a JDM ZC for my '88 civic and I bought some Eagle rods and some SRP forged pistons and rings to go with. What else am I going to have to do to allow the bottom end to handle some horsepower? I am building up this engine to handle a 75 shot of n20 and about every bolt...

For a CRX I would go with the B16. For one the the CRX is a really light car and having the highend horse power will be nice, and there is about unlimited after market support for the B16, with little time and money your little CRX could be one hell of a street machine! Plus, VTEC kicks ass, so...

I just recently bought a JDM ZC and I was wondering what kind of parts from the D-series will fit. I want to get larger throttle body and fuel rail and regulator among other things. Can I just buy parts for the D16 or is everything going to be mix and match? Also, does anybody know where I can...

I planning on doing a ZC swap and before I put it in I'm going to put in some pistons and rods. I am looking at SRP Forged Piston Set 2.963" Bore | 3.543" Stroke | 5.394" Rod | -3.2cc Dish. These are pistons are for the D16Z6, but I was wondering if they would fit. Also looking at the Eagle...

I am going to be putting a ZC in my '88 Civic and I want to add some high performance pistons and connecting rods and I was wondering where I could get these for a ZC. Or what cars could I buy some pistons for that would fit the ZC. Thanks for the help.