Search results for query: *

Getting ready to use uber, so I'm gathering all the stuff I need. Just wanted to know if this rom programmer is any good for burning roms? Cos I stay in South Africa I don't have access to too much. Help appreciated. Thanks

Had my Gotech MFI system installed a couple months ago (fully programmable fuel and spark management system from South Africa - www.gotech.co.za). It is set on Direct Fire. I had a cheap pirate coil (standard stuff) and after running for about 200km, she started misfiring and cutting out...

Is the Apexi SAFC any good to run a turbo D16A7 SOHC non-vtec? Will I need a missing link check valve?

When I pulled my long-side driveshaft out the other day, I saw that the end of the inner spline shaft (which locates inside the diff) was completely graunched just before the circlip, the rest of the spline was fine. So I got a new one and tried to put it in, but it just didn't want to clip in...

Was just thinking about other methods of forced induction and here is one idea I had, wondering if it would work.... here goes: Get one of those smallish air compressors used for spraying and stuff, charge it up with air pressure via the mains outlet and pipe it into your inlet. Obviously sort...

Bought a turbo off a guy, says its from the Nissan 200sx and that its a Garrett t25.... but looking at it, I think it might be a T3: This is what the turbine inlet flange looks like: ------------------------------ |....0.......................0....| |........|^^^^^^^|........|...

Got stock internals on D-series, got everything ready now to turbo, but still a little worried about compression. The pistons have been ceramic coated, but otherwise they are stock (0.20 thou over sized). The manual on my car says compression is 9.1:1 stock, but the block was decked and the head...

Looking for a good condition HF/STD manifold to turbo my D16. Dont need the o2 sensor. I stay in South Africa, so I'll need a price to ship it here too if possible. Please PM me if you can. Thanks!

I'm in the process of turbo'ing my D16A7 (1600cc, SOHC, non vtec). I've just had the engine management system installed (the system is a Gotech MFI, www.gotech.co.za for details). now I'm ready to sort out the fuelling. here are the specs: D16A7 motor with a Garrett T25 turbo (off the Nissan...

Saw these injectors on Ebay, 4 x brand new 450cc injectors that fit directly onto Honda fuel rail and manifold. $199 for set of four with 1 year free return warranty. see details: http://cgi.ebay.com/ebaymotors/ws/eBayISAP...sspagename=WDVW Do you guys think that they will be any good? Or...

Building a D-series bottom-end, nearing the end of engineering and was wondering, before i put everything back together if shotpeening the rods and using some high-strength conrod bolts will allow me to boost any higher, or would i just be wasting money?

Howzit all.. any idea if the injectors from the 200sx Nissan will work nicely on my D16a7 turbo (t25)? These are 2.5ohm, 350cc injectors. Too small? Will they fit the fuel rail easily? I will be running a gotech MFi (www.gotech.co.za)... Help?

Anyone got any idea what site I can go to to buy a plain clear, or red/clear taillights for the 91 CRX? I hunted high and low, but theres only that Altezza shit. I just want the plain taillights and reflective panel.?? help!

here's the deal... I work at a magazine in South Africa called Speed & Sound (www.speedandsound.co.za) as graphic designer. We recently featured a Toyota Conquest with a turbocharger and a supercharger installed. cool, I saw the motor and my collegue went for a drive with the guy, apparently it...

A mate of mine has just hooked me up with a Garret T25 for R400 (thats about $60). It's not new, but in good nick... off his Nissan 200sx. Next I'm sending it in to be acid bathed, new seals and bearing etc. My whole turbo setup that I'm planning is around the Edelbrock Drag turbo kit which...

Was at a site the other day, www.homemadeturbo.com/turbo_projects. This site features a good couple of D-series turbo's. Most of these jobs use what they quote is the "STD" manifold. Where is this manifold from? I heard a certain year CRX? Also is it ok to use this STD manifold for turbo...

Need some advice from you guys. Got a D16A7 (SOHC) 16v honda motor which I am currently building for forced induction. I couldn't find any low compression pistons down here in South Africa, but got a set of .20 thou standard pistons ceramic coated. The rest of the Sub-assebmbly is stock, stock...