Search results for query: *

I have a 90 civic Si that I bought 2 years ago. Saturday I drove it to work and back with no problems. It sat till Sunday night I tried to drive it and it wouldn't start. Main relay is less than a year old. The fuel pump primes and I pulled a spark plug out and I see spark. If I keep cranking...

I have a 90 Si, my ac compressor is not getting any power. I have hard wired it and it will kick on. Is there a relay or fuse somewhere that would cause it not to work? Could the ac button on the climate control be bad? Any help would be appriciated. I live in TX and its HOT!

Want power steering in my car if u have one let me know. THANKS!!!!

I have a 91 DA with a JDM B16a swap in it. I want to put my powering steering back in it. Will a upper power steering bracket (one bolted to head) work from a 99-00 Civic Si. If not what will?

I have a 90 integra with a obdo JDM B16a i can't afford a Skunk2 intake manifold yet so what other B-series manifolds can i use that will flow better than the stock B16a

I have a 91 da and the car will start but if i turn the lights or ac on it dies. Also my gas gauge does not work and the temp gauge goes straight to hot. If i turn the signal lights on it makes the temp gauge bounce back and forth also. If i drive it the speedometer goes back and forth and does...

I have complete b16a bottom end it has all the internals still intact was going to piece together a swap but bought a full B16a swap instead asking 300$ or BEST OFFER will trade for a PR3 OBDO ECU and some cash email me for pics i can ship if needed but its heavy and might be pricey

Just got a hold of a jdm b16a swap as for as parts like misc. gaskets, spark plugs,wires,timming belt, etc etc etc Should i ask for parts for a 92-95 Del sol si w/b16a or 92-93 Gsr B17a1 also its i bought it from a guy who bought it from Nippon motors should i replace the head gasket also or...

Just got a 91 teg and the ecu is throwing a code Flasssssssssh then flash flash flash im guessing that is a code 13 Atmospheric Pressure Sensor - Defective circuit or unplugged/ Defective sensor where is that located also it idles at 3000-4000 rpm's any body have some info on this

Will 94 integra seats work in a 1990 hatch?

I have a 90 civic hatch i drove it earlier and it started up fine. When i went to drive it again a hour later it wont start. It doesnt even crank over I put the key in the ignition and go to start it and it does nothing. I checked the battery and it has plenty of power lights turn on and radio...

I have a 90 hatch with a Ls in it and am using a Ls tranny as well with it. Sometimes my car wont go into gear. It does it at cold start and while a have been driving it. It doesnt matter if the tranny is hot or cold. I have checked the clutch cable and checked/changed the tranny fluid. It comes...

I have a 90 hatch with a Ls swap in it and am using a Ls cable type tranny. My car wont go into gear sometimes and other times it works without any problems. Is it a simple fix will replacing the clutch cable do the trick? Any time i mess with the clutch cable it seems to work.

Want to put ac in my 90 hatch it has a ls swaped in it what compressor do i use what lines? Before anybody says anything i live in TEXAS. Walking from your front door to your car will make you sweat during the summer. When it is 100 degress outside it feels like 120.

I just swapped a B18a1 into my 90 hatch. When i turn it on in the mornings it idles high 3000 rpms. After it warms up it idles up and down between 1000 and 2000 rpms i am using a 91 integra ecu. The ecu is not throwing any codes so unsure what it is i have checked my vaccum lines they seem...

I just recently did a mpfi swap on my 90 std hatch (w/stock engine)i am still having two problems. 1st one is if i use any other ecu besides a pm8 i get a code 4 which i have reserched is a CPS problem. I tried using a pm6,pg7,& a pr4 all obdo. I dont get this problem at all if i use the pm8...

I have a 90 hatch std w/mpfi conversion done already and want to do a mini me swap. i have a d16z6 head and wanted to know if i could use a d16y7 block? If i can do i have to run oil to the vtec solenoid (like ls/vtec)? Is it just like doing a regular mini me swap or is there more to it? What is...

I have a 90 hatch std and i convereted to MPFI all wiring is done correctly. When i plug in a PG7 or PM6 ecu i get a code 4 (cps) on the ecu. If i plug in my old CRX Hf ecu PM8 i get no codes and it runs fine. Could i have the incorrect distributor. Is there a difference between a CRX Hf dist...

I have a 90 hatch std and i convereted to MPFI all wiring is done correctly. When i plug in a PG7 or PM6 ecu i get a code 4 (cps) on the ecu. If i plug in my old CRX Hf ecu PM8 i get no codes and it runs fine. Could i have the incorrect distributor. Is there a difference between a CRX Hf dist...