Search results for query: *

What the maximum speed I should be able to go in 1st gear, I have no tach so I need a reference. I have a stock JDM H22a.

I’m having v-tec problems with my h22 accord and I need to know the following. 1 I just pulled a code and I’m getting a code 12 which is the Egr valve could this be a possible reason. 2 My tach does not work, I’m not sure if it’s the tach itself or the blue wire on the dizy is not...

I have a 92-01 H22 complete shifter assembly which includes, shifter cables, shifter (OEM), plate and all rubber spacers etc. Very clean little to no rust came off a prelude with only 80k 110 shipped. I have a h22 manifold no throttle 75 shipped. I also have H22 wireharness complete and...

Anyone have a knock sensor lying around if so email or pm willing to buy it.

I just finished up my prelude to accord swap and everything seems to be running fine. However, have a few weird things going on. 1st when I start the car, the car does not want to go in any gear at all. I have to play with the shifter then eventually it will start working, until I restart the...

I'm using a b16 ignition coil and igniter with an accord ECU on my JDM h22a would this set up cause my tact no to work. I believe the coil is responsible for the tact readings.

Does anyone have a complete H22a throttle body with all sensors etc. If so pm willing to buy.

I have a very specific question is the crank pulley bolt on the 94 USDM H22 crank the same bolt that goes on the 95 JDM H22 crank. I ask because My JDM H22 is in the process of being rebuilt and my original JDM crank had to be replaced. I got a new crank from someone who claims it came from a 94...

Is it true if you remove you power steering belt, and run no power steering that in time because power steering fluid is not circulating in the rack. That eventually the rack with become faulty or damaged.

Has anyone successfully used an accord power steering assembly on a h22 swap yet. If so could someone explain to me what was necessary and steps that were used to do this.

I have a question about the IAB sensor on the prelude (JDM 92-96) engine. 1 Does the sensor throw a code if the wiring is not done right? 2 Exactly what needs to be wired if I have an ex 5gen accord? 3 I heard I can simply connect a vacuum hose from the mechanism that opens and closes the...

Does anyone have any spair H22A1 92-96 single piston rod laying around. If so i'd be willing to buy it so hit me up thx. Massivebicep@aol.com

Hey I need a crank shaft in near or perfect condition with no scratches or grooves nor rust ASAP, it has to be from a 92-97 prelude only because these shafts use 50mm main bearing and the 98 and up use the 55mm bearings. My car is setting in a shop and waiting for this part. Willing to buy...

Is the crank that comes from a 2002 obd2 prelude the same crank that is a JDM 92-95 h22a ob1 engine? I know that the JDM is a closed deck block and the newer prelude engines 97 and up are open deck but does it matter? I also want to know if the piston rods are the same as well. I’m in the...

So far this is the best bang for my buck that ive seen. Does anyone know anything about this brand. F1 STAGE 3 Clutch & X-LITE RACING Flywheel - PRELUDE. Here is the ebay auction number 8049124854 tell me what you guys think.

I going to be buying a light weight flywheel and I was wondering if I should go with FIDANZA ALUMINUM FLYWHEEL which is only 8lbs or ACT streetlite ALUMINUM FLYWHEEL which is 11.1 pounds. I’ve been doing some reading and learned that a flywheel that’s too light less than 10 pounds is not...

In the process of buying some parts for my H22A for a rebuild, on line though I only see parts for a H22A1 (USDM) and not for the H22A (JDM). My question is since the JDM H22A, the motor I have has a higher compression than the USDM motor. What exactly could I use form a USDM H22A1 without...

Is the Flywheel that comes from a 95 ex 5 speed accord the same flywheel found on a 92-95 JDM H22a

Ok guys just to make a long story short, I got screwed on eBay with a JDM H22A. So now I’m trying to turn a negative into a positive. Since the 2nd and 4th cylinders are pretty much blown (very low compression) I will now do a rebuild and hopefully end up with a much better motor then I could...

Does anyone know what the compression should be for a 92-96 JDM H22a with 10.6 compression. I’m in the process of buying another engine from an importer the engine they have for sale tested 180 across in all cylinders. Is this good or just average engine has 46,000 thousand miles on it.