Search results for query: *

first, my car.. '89 civic hatch. SOHC ZC (d16a6) 5 spd. ok, im throwing code 63 and the car seems to be misfiring. code 63 is (i looked it up): o2 sensor heated i recently put an exhaust on my car.. a cheap E-bay 4-2-1 header and a Monza Pacesetter cat-back system. the Monza kit has a lot of...

i was wondering if theres any way to get the play outta the shifter on my '89 civic 5 speed. ive already got energy suspension shifter stabilizer bushings, and htey helped a little, but not enough. i'd LIKE to have it more like a rifle bolt, or like a newer cars shifter ya know? i doubt THAT...

ok.. i was driving my honda (89 dx w/e SOHC ZC) and i heard it backfire from the IM. i know it kinda boggs a bit from 1/2 to full throttle, but this time it backfired! im running a PM6 ECU.. idk whats wrong.. im going to check my timing tomorrow.. all my fuel system is stock.. AHH! help!

ok.. just got my SOHC ZC in my 89 DX and i did the MPFI swap before.. but i have an odd question. when i get on the throttle, there is NO change in performane when comparing anything past 1/4 throttle other than noise from the engine. the further i push the gas, the engine kinda humms.. its the...

just got done with my ZC swap.. everything is working fine.. except im getting a CEL. code 5.. 5- Accord Civic CRV CRX Del Sol Odyssey Prelude 85-98 * 86-98 97-98 85-91 93-97 96-98 85-98 MAP Sensor (Manifold Absolute Pressure) mechanical problem / disconnected piping * exc 94-95 there is one...

while doing my swap, i noticed that my passenger side tie rod end was pretty fucked. the rubber boot thing around the bolt was tore to shit, and the joint was exposed and the grease was alll kinds of nasty. so i went to the parts store and picked a new one up.. i cant get the old one off!!! i've...

im finishing up my SOHC ZC swap into my '89 dx. and right now im trying to put the axles back into the tranny.. i can get them to go about half way, maybe a bit more, then they just wont go any further! is there any tricks to getting 'em in the rest of hte way? or should i just take a hammer to...

i was thinking.. a cool idea for the honda-swap would be a troubleshooting section. like a moderator only area where they post troubleshooting guides for us cursed automotives to read and fix our problems.. just a thought i wanted to throw out there.. :-D

i got the new engine for my swap today and im changing the timing belt and i need help with the crank pulley. i know they're supposed to be a PITA to get off, and i know it takes a few hours, a long breaker bar, and a few pain pills for your back afterward lol. but do you guys have any good...

after my swap, i plan on picking up either an Si cluster, or a tach from autometer. i wanted to do a lil learnin on how to wire it up before i go all headlong into it. i've done some searching and didnt find anything how-to wise.. where do i wire from and to!? any ideas? thanks

i've swapped a SOHC ZC engine into my '89 DX hatch and now i need to pick up an Si transmission to get the car a bit more like what i want.. anyone have a good Si trans they're willing to part with for relatively cheap?! I want to save going to the junkyard as a last resort because it'll be a...

ok. i ordered my engine from HMotors.com last week some time. over the phone, they said it'd be here today (tuesday). today, i got a call from the drop company saying that they'll get it here on friday.. i guess, Hmotors gets the engine in TOWN today, then the other company gets it here to my...

ive got everything for my swap ordered except for the new motor mounts. the stockers are falling apart!! ive heard TONS of good stuff about the hasport poly-euro's, but i cant find any to replace my mounts for the D-series engine, they're all for B, H, and K series engines! do they sell mounts...

so.. now im going to buy a new SOHC ZC to replace my current one in my '89 hatch. right now, the only place i have to do the swap, is in my home garage. before, we did the swap in my school's auto shop. at home, i have a floor jack and jack stands. i will be getting an enjine lift to pull out...

ok.. so far ive ruled out everything but buying another ZC/d16a6 and throwing it in to replace my blown ZC.. its been about a year since the original swap and ive forgotten everything that i replaced with the new engine before.. what should i buy new before i put the new engine in? i was...

anyone know of a place that sells honda engines? i want to try to get the engine from a reliable place.. or anyone have a D16A6 they wana sell?

i snapped a rod in my honda yesterday.. and now i have to decide whether to rebuild the engine with new parts, or scrap the car and try to scrape together the cash for a new car.. do you guys think it'd be worth the money to buy new rods, bearings, pistons, and rings? i know i'd be looking at...

i was driving the honda last night, and then out of no-where, i heard a loud 'flump' type of sound from the engine bay and then my oil pressure QUICKLY dropped.. i put the car in neutral, threw on my hazzards, and turned the car off, coasted to a gas station where i could get it towed from...

i just got my honda running again, and remembered that before it died before, that my speedometer wasnt working.. so.. where, on an '89 civic DX (manual trans) would the VSS be located? i know its on the transmission somewhere, but where exactly is it? i cant find it! lol. is it hard to get to...

i got my DPFI to MPFI swap done on my D16A6 in my '89 civic hatch (DX) and it started up, and ran like a champ! i turned it off to put come coolant in it, and when i went to start it again, wouldt start. it cranks, but just wont start i have spark, and i have gas, but it wont start. it tries...